Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
- Line six-cylinder engine
   General information
   Repair procedures which implementation is possible without extraction of the engine from the car
   Reduction in the provision of VMT of a step of compression of the piston of the first cylinder
   Removal and installation of a cover of a head of cylinders
   Removal, check of a state and installation of yokes and bars of pushers
   Replacement of valvate springs, their plates and maslootrazhatelny caps
   Removal and installation of the inlet pipeline / final collector
   Removal and installation of a head of cylinders
   Replacement of a forward epiploon of a bent shaft
   Check of a state, removal and installation of a cover of a distributive chain, chain and its asterisks
   Removal, check of a state and installation of the camshaft, bearings and hydraulic pushers
   Removal and installation of the pallet of a case
   Removal, check of a state and installation of the oil pump
   Removal and installation of a flywheel / driving disk
   Replacement of a back epiploon of the crankshaft
   Check of a state and replacement of rubber pillows of support of the engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Removal and installation of a flywheel / driving disk

Removal

 PERFORMANCE ORDER

  1. The car also establish to Poddomkratta it on props, then remove transmission (The head the Manual box of gear shifting). In case of existence of signs of leaks it will be a high time to replace a forward epiploon / a sealing ring of the oil pump now (AT only).
  2. Remove a basket and the conducted clutch plate (The head Stsepleniye and the transmission line) (RT). Now it is a high time to check a state / to replace components of coupling and the directing bearing.
  3. Paint or center punch mark the provision of a flywheel / a driving disk in relation to a bent shaft for a guarantee of its correct installation at assembly.
  1. Before removal of a flywheel / a driving disk mark its situation in relation to a bent shaft.
  1. Give bolts of fastening of a flywheel / a driving disk to a bent shaft. If the bent shaft at the same time begins to be turned, immobilize it, having jammed the screw-driver between flywheel wreath teeth or having used mount as the lever.
  1. At an otdavaniye of fixing bolts hold a flywheel from a provorachivaniye by means of the lever.
  1. Remove a flywheel / a driving disk from a bent shaft. As the weight of a flywheel is rather big, take care of its adequate support in process of an otdavaniye of the last bolt.

Edges of a gear wreath can be very sharp - put on gloves.

Installation

 PERFORMANCE ORDER

  1. Wipe a flywheel, having removed from it traces of oil and lubricant. Check a flywheel surface for existence of the cracks left heads of rivets of furrows, spots of an overheat and zadir. Superficial scratches can be removed by means of a thin emery paper. Lay a flywheel on a flat surface and by means of the measuring instrument of planeness check it for existence of signs of a bend and deformations. In case of detection of serious defects the flywheel should be given to a pro-point in a workshop of car service.
  2. Smooth out also the interfaced flywheel surfaces / a driving disk and a bent shaft, check their state. If the back epiploon of a bent shaft allows leaks, replace it before you begin to establish a flywheel / a driving disk into place (Section Replacement of a Back Epiploon of the Crankshaft).
  3. Apply a flywheel / driving a disk to a bent shaft. Track combination of the landing tags put during dismantle. Pay attention that some engines are equipped with the directing pins or unevenly located bolted openings that does landing of a flywheel / a driving disk on a shaft quite unambiguous. Before installation of bolts grease their carvings with the fixing sealant.
  4. Jam the screw-driver in wreath teeth for keeping of a flywheel / a driving disk from a provorachivaniye and tighten fixing bolts with the required effort, working in slightly (three) stages and passing from a bolt to a bolt in a diagonal order.

It is useful to note a head of each tightened bolt chalk - it will allow to observe a due order of tightening and to avoid the admission of bolts.

  1. You make further assembly as it should be, the return to a dismantle order.