Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
- Settings and routine maintenance
   - Schedule of routine maintenance of Jeep Cherokee
      Introduction
      General information on settings
      Checks of levels of liquids (each 400 km (250 miles) of a run or weekly)
      Check of a condition of tires and pressure in them (each 400 km (250 miles) of a run or weekly)
      Check of level of liquid of automatic transmission (each 400 km (250 miles) of a run or weekly)
      Check of level of liquid of system of hydrostrengthening of a wheel (each 4800 km (3000 miles) of a run or time in 3 months)
      Change of motive oil and oil filter (each 4800 km (3000 miles) of a run or time in 3 months)
      Check and service of the battery (each 4800 km (3000 miles) of a run or time in 3 months)
      Check of serviceability of the cooling system (each 4800 km (3000 miles) of a run or time in 3 months)
      Check of a state and replacement of the hoses passing under a cowl (each 4800 km (3000 miles) of a run or times in 3 months)
      Check of a state and replacement of brushes of screen wipers (each 4800 km (3000 miles) of a run or time in 3 months)
      Check of a condition of a suspension bracket and steering
      Check of a condition of system of production of the fulfilled gases (each 12 000 km (7500 miles) of a run, or time in 6 months)
      Check of level of gearbox oil of the manual transmission (RKPP) (each 12 000 km (7500 miles) of a run, or time in 6 months)
      Check of level of oil of the transfer case of all-wheel drive (4WD) models (each 12 000 km (7500 miles) of a run, or time in 6 months)
      Check of level of oil of differential (each 12 000 km (7500 miles) of a run, or time in 6 months)
      Rotation of wheels (each 12 000 km (7500 miles) of a run, or time in 6 months)
      Check of a condition of brake mechanisms (each 12 000 km (7500 miles) of a run, or time in 6 months)
      Check of a condition of components of a power supply system (each 12 000 km (7500 miles) of a run, or time in 6 months)
      Check of a state, adjustment of a tension and replacement of a driving belt (each 12 000 km (7500 miles) of a run, or time in 6 months)
      Check of a condition of seat belts (each 12 000 km (7500 miles) of a run, or time in 6 months)
      Check of functioning of the sensor switch of permission of start (only models with AT) (each 12 000 km (7500 miles) of a run, or time in 6 months)
      Chassis lubricant (each 12 000 km (7500 miles) of a run, or time in 6 months)
      Replacement of the air filter (each 48 000 km (30 000 miles) of a run, or time in two years)
      Replacement of liquid and the filter of automatic transmission (each 48 000 km (30 000 miles) of a run, or time in two years)
      Adjustment of tapes of the automatic transmission (AT) (model since 1994 of the issue) (each 48 000 km (30 000 miles) of a run, or time in two years)
      Replacement of gearbox oil of a manual box (switching) of transfers (RKPP) (each 48 000 km (30 000 miles) of a run, or time in two years)
      Change of oil of the transfer case (model 4WD) (each 48 000 km (30 000 miles) of a run, or time in two years)
      Differential oil change (each 48 000 km (30 000 miles) of a run, or time in two years)
      Service of the cooling system (depletion, washing and filling) (each 48 000 km (30 000 miles) of a run, or time in two years)
      Check of a state and replacement of the valve of system of the operated ventilation of a case (PCV) (V8 engines) (each 48 000 km (30 000 miles) of a run, or time in two years)
      Check, clearing and replacement of a hose of system of continuous ventilation of a case (CCV) (the 6th cylinder engines) (each 48 000 km (30 000 miles) of a run, or time in two years)
      Check of serviceability of functioning of system of catching of vapors of fuel (each 48 000 km (30 000 miles) of a run, or time in two years)
      Cleaning of the filter of ventilation of a case (V8 engines) (each 48 000 km (30 000 miles) of a run, or time in two years)
      Replacement of the fuel filter (each 48 000 km (30 000 miles) of a run, or time in two years)
      Replacement of spark plugs (each 48 000 km (30 000 miles) of a run, or time in two years)
      Check of a condition of candle wires, a cover and the runner of the distributor (each 48 000 km (30 000 miles) of a run, or time in two years)
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Chassis lubricant (each 12 000 km (7500 miles) of a run, or time in 6 months)

Prepare lubricant of the required grade (see subsection the Recommended lubricants and liquids of Specifications for this Chapter). Also lubricant gun (syringe) is required. If instead of lubricant unions in components of the chassis of your car caps are established, it is necessary to buy as well unions.

Materials and tools necessary for lubricant of elements of the chassis and body of the car.

1 — Motive oil - the Liquid motive oil placed in a butterdish of this kind can be used for greasing of loops of doors and a cowl
2 — Grafitsoderzhashchaya the aerosol - Is applied to greasing of cylinders of locks
3 — Lubricant - the lubricants of various density and types good for application in the lubricant gun (syringe) Are produced. Be verified with requirements of Specifications to grades of lubricants in each separate case
4 — the Lubricant gun (syringe) - In a picture is shown usual type the lubricant gun (syringe) with the removable hose equipped with a special nozzle for putting on on lubricant unions of components of the chassis of the car. After application carefully wash out the gun!

 PERFORMANCE ORDER

  1. Glance under the car and on the place get acquainted with an arrangement of lubricant unions.
  2. For simplification of access under the car also establish to its poddomkratta on the prop frames got under elements. Make sure of reliability of fixing of the car in the lifted situation. If it is also supposed to make rotation of wheels, do not forget to weaken nuts of their fastening before the car is lifted above the ground.
  3. Before starting implementation of the procedure squeeze out a little lubricant from a nose of the gun (syringe). Dry wipe a nozzle with pure rags.
  4. Get under the car, having taken with themselves enough pure rags and the lubricant gun (syringe) and start greasing of components of the chassis.
  5. Absolutely wipe the lubricant union and densely press to it a gun nozzle. Having rocked the gun handle, squeeze out lubricant in a component. Stuffing of spherical hinges is made until their rubber covers do not become firm to the touch. Be not overzealous - excess of lubricant can lead to damage of a cover. Other details of a suspension bracket and steering have to jam until the beginning of a vystupaniye of lubricant through a joint of two components. If lubricant begins to be squeezed out from under a gun nozzle, it is necessary to check whether the nipple of the lubricant union was hammered, and also to make sure of reliability of fastening of a nozzle on the union. Perezakrepite a nozzle also repeat attempt. In case of need change the lubricant union.
Access to the lubricant union of the top spherical support is provided by removal of a forward wheel.

Fill lubricant in the union of a spherical support until its cover does not become firm to the touch.

  1. Erase excess of lubricant from a component and the union and repeat the procedure for all remained unions/components.
  2. Grease the sliding driveshaft joint, having pumped up lubricant in the union until the beginning of expression it through the sliding joint.

The lubricant union of the sliding hinge of the forward driveshaft is located on the face plug - pump up lubricant until it does not begin to be squeezed out from the plug.

  1. Grease the contact surfaces of the mechanism of switching of the transfer case with pure motive oil.
  2. Without being chosen from under the car, grease a cable of the drive of the parking brake, its guides and levers. It is made by drawing a small amount of lubricant for the chassis on a cable and components of the drive of a brake by fingers.