Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car

Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
- Body
   General information
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Service of loops and locks
   Replacement wind and motionless glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of the lock of a cowl and cable of its drive
   Removal and installation to the place of the panel of a decorative front grille
   Removal and installation of a forward wing
   Removal and installation of bumpers
   Removal and installation of the panel of an internal upholstery of a door
   Removal, installation and adjustment of provision of a door
   Removal and installation of handles, cylinder and clamp (latch) of the lock of a door
   Removal and installation of a windowpane of a door
   Removal and installation of the regulator of a window of a door
   Removal and installation of the central console
   Removal and installation of the panel of an upholstery of a door of a back
   Removal, installation and adjustment of provision of a door of a back
   Replacement of an emphasis of a door of a back
   Removal and installation of facing of a combination of devices
   Removal and installation of facings of the control panel
   Removal and installation of the control panel
   Removal and installation of covers of a casing of a steering column
   Removal and installation of rear-view mirrors
   Remove also installation of a lattice of a fairing
   Removal and installation of seats
   Control body sizes
+ System of onboard electric equipment
+ Governing bodies and methods of operation

Removal, installation and adjustment of provision of a cowl

The cowl is rather heavy element of a body and installation represents it sufficient a difficult procedure. Removal and installation of a cowl it has to be made by forces of at least two people.

Removal and installation


  1. For protection in the course of removal of a cowl of the painted surfaces of a fairing and wings of the car cover them with blankets and whether the covers which are specially released for this purpose.
  2. Mark the provision of loops concerning a car body for a guarantee of the correct installation of a cowl at assembly (use a chertilka, a marker or easily washing away paint).
  3. Disconnect everything the cables and wires preventing removal of a cowl.
  1. Before removal of a cowl disconnect from it a plait of wires of a lamp of illumination of a motive compartment.
  1. By means of the assistant who will support a cowl give nuts of fastening of loops to it.
  2. Lift a cowl.
  3. You make installation upside-down.



  1. Longitudinal and cross adjustments of provision of a cowl in an aperture of a motive compartment are carried out by shift it concerning plates of loops after preliminary weakening of bolts of their fastening.
  2. For assessment of size of shift of a cowl lead round plates of loops.
  3. Weaken fixing nuts and displace a cowl (not on many for each approach), as appropriate correcting its situation. Tighten fixing nuts (or bolts), carefully close a cowl and check correctness of its situation.
  4. Adjust the provision of shock pillows on a radiator support so that the cowl when closing appeared aflush with the top panels of wings.
  5. The provision of assembly of a clamp of the lock on a cowl can be also adjusted in the longitudinal or cross directions after weakening of fixing bolts.
  6. The lock, also as well as loops, have to be greased regularly with white lubricant on a lithium basis in order to avoid a souring and extension of service life (wear reduction of speed).