Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
- Body
   General information
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Service of loops and locks
   Replacement wind and motionless glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of the lock of a cowl and cable of its drive
   Removal and installation to the place of the panel of a decorative front grille
   Removal and installation of a forward wing
   Removal and installation of bumpers
   Removal and installation of the panel of an internal upholstery of a door
   Removal, installation and adjustment of provision of a door
   Removal and installation of handles, cylinder and clamp (latch) of the lock of a door
   Removal and installation of a windowpane of a door
   Removal and installation of the regulator of a window of a door
   Removal and installation of the central console
   Removal and installation of the panel of an upholstery of a door of a back
   Removal, installation and adjustment of provision of a door of a back
   Replacement of an emphasis of a door of a back
   Removal and installation of facing of a combination of devices
   Removal and installation of facings of the control panel
   Removal and installation of the control panel
   Removal and installation of covers of a casing of a steering column
   Removal and installation of rear-view mirrors
   Remove also installation of a lattice of a fairing
   Removal and installation of seats
   Control body sizes
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Removal and installation of the control panel

Details of installation of the control panel


See the prevention at the beginning of the Section Removal and installation to the place of the panel of a decorative front grille.


 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Remove a lattice of a nozzle of an obduv of a windshield, facing of a combination of devices, covers of a casing of a steering column, the knee lock and facing of the panel of switches (see the Sections Removal and installation of facing of a combination of devices, Removal and installation of facings of the control panel and Removal and installation of covers of a casing of a steering column).
  3. Disunite the electric socket of a plait of wires of a steering column, give nuts of a column and lower the last on a driver's seat.
  4. Remove panels of the left and right side fairing and shock panels. Disunite the electric socket and a wire of the antenna from the right side shock panel.
  5. Remove the handle of the drive of opening of a cowl (The section Removal and installation of the lock of a cowl and cable of its drive).
  6. Remove the central floor console (The section Removal and installation of the central console).
  7. Remove the radio tape recorder (The head Sistema of onboard electric equipment) and the control panel of the air heater/conditioner (The head of the Cooling system, heating and air conditioning).
  8. Disunite the electric socket of a partition of the control panel and disconnect a plait of wires in the left lower part of a board.
  9. Disconnect electric and vacuum lines of the heater/conditioner of air.
  10. Remove facing of the dashboard.
  11. Give four top nuts of fastening of the control panel. Give the left and right fixing screws of the control panel. Give the screw behind an ashtray and the screw over a steering column. Give two screws on the left arm of the central console.
  12. Delay the control panel for ensuring access and a rassoyedineniye of the remained electric sockets back.
  13. By means of the assistant remove the control panel from the car.
  14. You make installation upside-down.