Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
- Body
   General information
   Care of a body
   Care of the finishing panels manufactured of vinyl
   Care of an upholstery and rugs of salon
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Service of loops and locks
   Replacement wind and motionless glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of the lock of a cowl and cable of its drive
   Removal and installation to the place of the panel of a decorative front grille
   Removal and installation of a forward wing
   Removal and installation of bumpers
   Removal and installation of the panel of an internal upholstery of a door
   Removal, installation and adjustment of provision of a door
   Removal and installation of handles, cylinder and clamp (latch) of the lock of a door
   Removal and installation of a windowpane of a door
   Removal and installation of the regulator of a window of a door
   Removal and installation of the central console
   Removal and installation of the panel of an upholstery of a door of a back
   Removal, installation and adjustment of provision of a door of a back
   Replacement of an emphasis of a door of a back
   Removal and installation of facing of a combination of devices
   Removal and installation of facings of the control panel
   Removal and installation of the control panel
   Removal and installation of covers of a casing of a steering column
   Removal and installation of rear-view mirrors
   Remove also installation of a lattice of a fairing
   Removal and installation of seats
   Control body sizes
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Removal and installation of handles, cylinder and clamp (latch) of the lock of a door

Door latch

 PERFORMANCE ORDER

  1. Completely lift glass of a window and remove the panel of an internal upholstery of a door and the water filter (The section Removal and installation of the panel of an internal upholstery of a door).
  2. Disconnect rods of drafts from a latch.
  1. Turn a plastic clamp up and disconnect rods of drafts of a latch.
  1. Give three fixing screws with heads like TORX. Perhaps, moving of screws will require an impact driver.
  1. Give a bolt of fastening of a latch.
  1. Remove a latch from a door.
  2. Apply a latch on the adjusting place and screw fixing bolts. Strongly tighten bolts.
  3. Connect rods of thirsts to a latch.
  4. Make sure of adequacy of locking of a door. In case of need make adjustment of provision of a latch (having weakened for this purpose bolts), trying to obtain ease of a zashchelkivaniye of a door (the door handle at the same time has to appear aflush with a door surface). After completion of installation weaken the adjusting screw of draft, having passed a key hexagon 5/32 inches (4,0 mm) throughout an access opening in a door end face. Weaken the adjusting screw and push it up a cut for the choice of a weak point of draft, then tighten the screw.
  1. Pass a key hexagon a head throughout an adjusting opening, weaken the screw and advance it up a cut for selection of a weak point of draft.

Lock cylinder

 PERFORMANCE ORDER

  1. Remove the external handle of a door. Disconnect draft, having used the screw-driver for pushing out of the holder and extraction of the cylinder of the lock from a door.
  2. You make installation upside-down.

External handle

 PERFORMANCE ORDER

  1. Disconnect draft of the external handle (the remote drive) of a door from a lock latch, give fixing nuts and remove the handle from a door.
  1. Details of installation of the external handle and cylinder of the lock of a door.
  1. Install the handle into place, connect draft and screw nuts. Strongly tighten nuts.

Internal handle

 PERFORMANCE ORDER

  1. Give a fixing bolt, turn the handle forward and disconnect drafts, then remove the handle from a door.
  1. Give a bolt (shooter), turn the internal handle forward and disconnect rods of drafts.