Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   General information
   Removal and installation of the forward stabilizer of cross stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a steering wheel
   Check of a state, removal and installation of the steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Pumping of system of hydrostrengthening of a wheel
   Wheels and tires - the general information
   The angles of installation of forward wheels - the general information
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Removal and installation of rotary fists

The procedure is applicable as all-wheel drive models, and to models 2WD. During the work on model 2WD just lower the moments concerning only components of all-wheel drive cars.

Removal

 PERFORMANCE ORDER

  1. Weaken nuts of fastening of a wheel, the car and establish to a poddomkratta it on props. Remove a wheel.
  2. Disconnect steering draft (The section Removal and installation of the steering mechanism) from a rotary fist.
  3. Remove a support and a disk of the brake mechanism (The head the Brake system).
  4. Remove a nave of the forward bridge and bearing assembly, then remove a power shaft (The head Stsepleniye and the transmission line).
  5. Disunite the electric socket of the ABS sensor of a wheel and remove the sensor.
  1. Disunite the electric socket of the ABS sensor of a wheel, give a fixing bolt (shooter) and remove the sensor.
  1. Take forelocks and weaken - but do not remove - koronchaty nuts of hairpins of spherical support. For removal of a fist from hairpins of spherical support knock on it from above with the hammer or use a small stripper.
  1. If the obstukivaniye of the top part of a rotary fist does not help its removal from a hairpin some of spherical support, use a small stripper (in a picture the stripper is established on a hairpin of the top hinge; removal of a fist from a hairpin of the lower support is made similarly).
  1. Carefully check a fist for existence of cracks, paying special attention to the steering lever and the site of landing of a spindle. Check openings under fingers of spherical support for ovality existence. In case of identification of any of the listed defects replace a fist.

Installation

 PERFORMANCE ORDER

  1. Establish a rotary fist on a forked beam of the bridge and insert into openings of a hairpin of spherical support in it. Screw nuts and tighten them with the required effort. Block nuts forelocks.
  2. Establish into place a power shaft (The head Stsepleniye and the transmission line).
  3. Establish assembly of a nave with the bearing (The head Stsepleniye and the transmission line).
  4. Establish a disk and a support of the brake mechanism (The head the Brake system).
  5. Connect steering thirst for a rotary fist (The section Removal and installation of the steering mechanism).
  6. Establish a wheel and nuts of its fastening. Lower the car on the earth and tighten nuts of fastening of a wheel with the required effort (The head Nastroyki and routine maintenance).