Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   General information
   Removal and installation of the forward stabilizer of cross stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a steering wheel
   Check of a state, removal and installation of the steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Pumping of system of hydrostrengthening of a wheel
   Wheels and tires - the general information
   The angles of installation of forward wheels - the general information
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Removal and installation of screw springs of a forward suspension bracket

Removal

 PERFORMANCE ORDER

  1. Weaken nuts of fastening of wheels, a front of the car and establish to a poddomkratta it on props. Remove wheels.
  2. Mark situation and disconnect the forward driveshaft from the holder of a crosspiece of the leading gear wheel of differential (The head Stsepleniye and the transmission line), then tie up a shaft aside a piece of a wire.
  3. Prop up assembly of the bridge the jack got under differential or, what is more preferable, two jacks - on one from each of the sides of the bridge (the last way will provide the best balancing). Otboltite from the bridge the lower levers of a suspension bracket (The section Removal and installation of levers of a forward suspension bracket).
  4. Otboltite connecting links (racks) of the stabilizer and shock-absorbers of a suspension bracket from the forward bridge (The sections Removal and installation of the forward stabilizer of cross stability and its plugs and Removal and installation of forward shock-absorbers).
  5. Disconnect a jet bar (The section Removal and installation of a cross jet bar of a forward suspension bracket) from a bridge arm.
  6. Disconnect average steering draft from a bipod of the steering mechanism (The section Check of a State, removal and installation of the steering drive).
  7. Slowly omit assembly of the bridge so that springs completely stretched. If the bridge is propped up by only one jack, ask the assistant to support its right edge in the course of lowering of the bridge. Remove the holder of a spring and take a spring from under the car.
  1. Details of fixture of a screw spring - after the spring will be completely stretched give a bolt and remove the holder, then take a spring through space between the bridge and a frame.
  1. Check a spring for existence of the defects and traces of corrosion capable to be the reason of its premature exit out of operation.

Installation

 PERFORMANCE ORDER

  1. Establish a screw spring on a bridge case, impose the holder on the lower round of a spring and strongly tighten a bolt of fastening of the holder.
  2. Lift the bridge in adjusting situation and connect the lower levers of a suspension bracket (The section Removal and installation of levers of a forward suspension bracket) to its case. Tighten fixture with the required effort.
  3. Connect average steering thirst for a bipod of the steering mechanism (The section Check of a State, removal and installation of the steering drive).
  4. Fix a jet bar in the arm on the bridge (The section Removal and installation of a cross jet bar of a forward suspension bracket).
  5. Connect to a forward part of a case of the bridge of a rack of the stabilizer and shock-absorbers (The sections Removal and installation of the forward stabilizer of cross stability and its plugs and Removal and installation of forward shock-absorbers).
  6. Connect the forward driveshaft to the holder of a crosspiece of the leading gear wheel of differential (The head Stsepleniye and the transmission line).
  7. Establish wheels and nuts of their fastening, then lower the car on the earth. Tighten nuts of fastening of wheels with the required effort (see Specifications to the Head Nastroyki and routine maintenance).