Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   General information
   Removal and installation of the forward stabilizer of cross stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a steering wheel
   Check of a state, removal and installation of the steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Pumping of system of hydrostrengthening of a wheel
   Wheels and tires - the general information
   The angles of installation of forward wheels - the general information
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Removal and installation of levers of a forward suspension bracket

In order to avoid sliding of a case of the bridge from the position that considerably would complicate the subsequent assembly, remove and establish each of suspension bracket levers serially.

Car front also establish to Poddomkratta it on props.

Top lever

 PERFORMANCE ORDER

  1. Give a nut and a bolt of fastening of the top lever to a bridge case arm.

Components of the right levers of a forward suspension bracket (the model 4WD is shown; for models 2WD the scheme is similar).

  1. For a detachment of the top lever of a suspension bracket from a case of the bridge give a nut (in a picture it is not visible) and a bolt (shooter), then take a bolt from an arm.
  1. Give a bolt and a nut of fastening of the top lever of a suspension bracket to an arm of a frame and take the lever from under the car.
  1. For a detachment of the top lever of a suspension bracket from a frame give this nut (shooter) and take a bolt (access to a head of a bolt is possible through the opening in a frame directed outside towards a wheel arch).
  1. Check the lever for existence of cracks and signs of deformation. Replace the damaged lever.
  2. Check the plug in a bridge case (only for the top lever) for existence of cracks, hardening and other signs of aging of material. If the plug needs replacement, install the lever into place and drive away the car in a workshop of car service or dealer office where this work will be performed by qualified specialists with use of the special tool without which existence removal of the plug is not possible.
  3. You make installation upside-down. Tighten all fixture with the required effort.

Lower lever of a suspension bracket

 PERFORMANCE ORDER

  1. By means of a chertilka or paint put down adjusting tags on cam regulators and the lever of a suspension bracket - it will give a guarantee of correctness of the subsequent assembly.
  1. Before a detachment of the lower lever of a suspension bracket from an arm of a case of the bridge mark situation concerning it the cam regulator, then give a nut and take a bolt.
  1. Give a nut of fastening of the lower lever of a suspension bracket to a bridge case arm, remove a cam and a bolt of a cam.
  2. Give a nut and a bolt on an arm of a beam of a frame and lower the lower lever.
  1. For a detachment of the lower lever of a suspension bracket from an arm of a frame give a nut (in a picture it is not visible) and take a bolt.
  1. You make installation upside-down. Take care of combination of tags of mutual position of the lever and cam regulator. Tighten all fixture with the required effort.