Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   General information
   Removal and installation of the forward stabilizer of cross stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a steering wheel
   Check of a state, removal and installation of the steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Pumping of system of hydrostrengthening of a wheel
   Wheels and tires - the general information
   The angles of installation of forward wheels - the general information
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Removal and installation of the pump of system of hydrostrengthening of a wheel

Components of the pump of system of hydrostrengthening of a wheel and its arms (V8 engine).

Components of the pump of system of hydrostrengthening of a wheel and its arms (6-cylinder engine)


 PERFORMANCE ORDER

  1. Weaken a tension of a driving belt and take off a belt from a pump pulley (The head Nastroyki and routine maintenance).
  2. By means of the syringe suck away from the tank of system of hydrostrengthening of a wheel perhaps more liquid. Establish drain capacity under the pump and disconnect from it high-pressure and returnable hydraulic lines. For improvement of access to a hose of the returnable line perhaps it will be required to remove an air cleaner casing (The head of the Power supply system and production of the fulfilled gases). Zakuporte the open ends of lines in order to avoid leak of liquid and hit in system of dirt.

Nipple connections of tubes and hoses of hydraulic lines of the pump.

  1. Give forward fixing bolts and back fixing bolts and nuts, then remove the pump from the engine.
  2. In case of need removals from the pulley pump at first measure vystupaniye size from its nave of a shaft of the pump. Remove a pulley from a shaft by means of a special stripper (for pulleys of pumps of systems of hydrostrengthening) - ask in shops of automobile accessories.

For removal of pulleys of pumps of system of hydrostrengthening of a wheel the stripper of such design is issued - ask in shops of automobile accessories.

  1. For landing of a pulley to a pump shaft the special tool, however from a long bolt, a nut, a washer and a replaceable face head of the same is also issued this time that the nave of a pulley of diameter can be independently made its equivalent. Pull a pulley on a shaft so that the shaft addressed over its nave at the same size that dismantle.
  1. For putting on of a pulley on a pump shaft the special tool is also issued, but …

… this time it can make replacement, having taken for this purpose a long bolt with the same step of a carving, as a carving in a pump shaft end face, a nut, a washer and a replaceable face head of the same outer diameter, as a shaft nave.

  1. You make installation upside-down. Upon completion of works do not forget to pump over system of hydrostrengthening of a wheel (Section Pumping of System of Hydrostrengthening of a Wheel).