Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   General information
   Removal and installation of the forward stabilizer of cross stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a steering wheel
   Check of a state, removal and installation of the steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Pumping of system of hydrostrengthening of a wheel
   Wheels and tires - the general information
   The angles of installation of forward wheels - the general information
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Removal and installation of the steering mechanism

Take care of that the steering shaft was not turned at the removed steering mechanism as it can lead to damage of a safety cushion. One of ways of blocking of a shaft is turning of a key in the ignition lock in position of LOCK. It is also possible to pass a seat belt through a steering wheel and to latch its buckle.

Removal

 PERFORMANCE ORDER

  1. Car front also establish to Poddomkratta it on props. Cock the parking brake.
  2. Establish drain capacity under a case of the steering mechanism (only for the mechanisms equipped with the hydraulic booster). Disconnect hoses/tube of hydraulic lines and a zakuporta the open ends for the purpose of minimization of losses of liquid and hit in system of pollution. In case of that existence, use for a detachment of lines a special key for cap nuts.
  3. Mark position of the lower cardan hinge of an intermediate shaft in relation to a main shaft of the steering mechanism. Remove the lower coupling bolt of an intermediate shaft.
  1. Weaken nuts of these nipple connections (arrow) and disconnect lines of system of hydrostrengthening of a wheel from a box of the steering mechanism, then mark position of the cardan hinge of an intermediate shaft in relation to a main shaft of the steering mechanism and weaken a coupling bolt.
  1. Give a nut of fastening of a bipod of the steering mechanism, remove a washer. Mark the provision of a bipod in relation to a shaft - at installation it has to be strictly observed.
  1. Before removal of a bipod mark its situation in relation to a shaft of the steering mechanism.
  1. By means of a two-gripping stripper separate a bipod from a shaft of the steering mechanism.
  1. For separation of a bipod from a shaft of the steering mechanism use a stripper.
  1. Holding the steering mechanism, give bolts of its fastening. Lower the block, disconnecting an intermediate shaft from a main shaft of the steering mechanism. Remove the steering mechanism from the car.

The steering mechanism fastens to a frame longeron by means of three bolts (arrow).

Installation

 PERFORMANCE ORDER

  1. Lift the steering mechanism in adjusting situation and connect an intermediate shaft, having tracked correctness of combination of tags.
  2. Establish fixing bolts with washers. Tighten bolts with the required effort.
  3. Put on a bipod a shaft. Make sure of correctness of combination of tags. Establish a washer with a nut and tighten the last with the required effort.
  4. Establish the lower coupling bolt of an intermediate shaft and tighten it with the required effort.
  5. Connect to a case of the steering mechanism of hoses/tube of hydraulic lines and add in the tank of system of hydrostrengthening necessary amount of liquid of the required grade (see Specifications to the Head Nastroyki and routine maintenance).
  6. Lower the car and pump over steering system (Section Pumping of System of Hydrostrengthening of a Wheel).