Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   General information
   Removal and installation of the forward stabilizer of cross stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a steering wheel
   Check of a state, removal and installation of the steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Pumping of system of hydrostrengthening of a wheel
   Wheels and tires - the general information
   The angles of installation of forward wheels - the general information
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Check of a state, removal and installation of the steering drive

Check of a state

The steering drive serves for connection of the steering mechanism with the operated wheels of the car and at the same time the friend in relation to the friend provides the adequate provision of wheels. Are a part of the drive: the bipod of the steering mechanism fastening its (mechanism) to a shaft and providing transfer of effort to average steering draft. Longitudinal back and forth motion of average draft is transferred to a rotary fist of the right wheel. Assembly of connecting draft serves for connection of average draft with a rotary fist of the second wheel. Connecting draft consists of a pipe, collars and two tips. The damper of the steering drive established between average steering draft and a frame of the car serves for decrease in vibrations and undesirable loads of components of the steering mechanism.

Components of the steering drive


 PERFORMANCE ORDER

  1. Establish forward wheels of the car in rectilinear situation and block a steering wheel.
  2. Poddomkratte one of car boats so that the wheel priotorvatsya from the earth approximately on 3 cm.
  3. Install the arrow dial measuring instrument, having pressed its plunger to the outer edge of a wheel. Undertake a wheel in forward and back points and pull it back and forth, monitoring indications of the measuring instrument. The maximum recorded value should not exceed 2,74 mm. If a side play the helmsman of system exceeds admissible, check each of axial points and spherical hairpins of the steering drive for existence of a weak point. In case of need make replacement of components.
  4. The car also establish to Poddomkratta it on props. Check covers of spherical hinges for existence of cuts, make sure of lack of the "stuck" hinges and damages or deformations of other components of the drive.

Removal and installation

Connecting steering draft

 PERFORMANCE ORDER

  1. Weaken nuts of fastening of wheels, the car and establish to a poddomkratta it on props. Cock the parking brake. Remove a wheel.
  2. Remove forelocks and weaken, but do not remove absolutely, koronchaty nuts of spherical hairpins of both tips of draft.
  3. By means of a small stripper separate tips of connecting steering draft from a rotary fist and average draft.

Use of a bifurcate divider of spherical hinges most likely will lead to damage of a cover of the hinge.


  1. Application of a two-gripping stripper for a detachment of a tip of connecting steering draft from a rotary fist - pay attention that the nut was only weakened, but is not removed completely; it allows to avoid a spontaneous partition of components.
  1. If connecting draft demands replacement, count quantity of naked rounds of a carving and write down result, for the purpose of respect for former convergence of forward wheels at assembly. Weaken a collar of a tube of the regulator and unscrew a draft tip.
  1. If the left tip of connecting steering draft is subject to replacement, count and write down quantity of the naked rounds of a carving which are sticking out of a tube of the regulator and roll a new tip taking into account these data.
  1. Grease a carving part of a tip of draft with lubricant for chassis components. Screw a new tip in a tube of the regulator and, screwing in draft in a tube, adjust distance from the last to a spherical hairpin, having left the same quantity of naked rounds of a carving that took place before dismantling (see the made record) (the number of naked rounds on both sides of the regulator should not differ one from another more than on three). Do not tighten regulator tube collars so far.
  2. For installation of assembly of connecting steering draft insert a spherical hairpin of its left tip into a rotary fist, and a hairpin of the right tip - in average draft. Screw nuts and tighten them with the required effort. If the spherical hairpin when tightening nuts is turned, crush it in a conical opening by means of big nippers.
  3. Install new forelocks. In case of need tighten a nut a little more for combination of the next spent on drink with an opening under the forelock in a hairpin.
  4. Tighten nuts of collars of a tube of the regulator with the required effort (see Specifications to the Head Nastroyki and routine maintenance). Drive away the car in a workshop on adjustment of angles of installation of forward wheels where corners will be checked and correctly are modified.

Average steering draft

 PERFORMANCE ORDER

  1. Car front also establish to Poddomkratta it on props. Cock the parking brake.
  2. Weaken, but do not remove, nuts of fastening of spherical hairpins of average draft to connecting drafts and to a rotary fist. Separate average draft from a rotary fist (see an illustration) and from connecting draft by means of a two-gripping stripper, then remove nuts.
  1. For a detachment of average steering draft from connecting draft use a small stripper.
  1. Following the same technology, separate average draft from a bipod of the steering mechanism. If the left tip of average steering draft demands replacement, perform procedures of items 5 and 6 of this Section.
  2. You make installation upside-down. If any of spherical hairpins it begins to be turned when tightening a fixing nut, drive it into a conical opening by means of big nippers. Tighten all fixture with the required effort.

Bipod of the steering mechanism

You watch the procedure of removal of a bipod of the steering mechanism in the Section Removal and installation of the steering mechanism.

Damper of the steering drive

 PERFORMANCE ORDER

  1. Car front also establish to Poddomkratta it on props.
  2. Disconnect a steering damper from average draft, having used the method described in item 2.
  3. Otboltite a damper from a frame also remove it from the car.
  4. You make installation upside-down. Tighten fixture of a damper with the required effort.