Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   General information
   Removal and installation of the forward stabilizer of cross stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a steering wheel
   Check of a state, removal and installation of the steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Pumping of system of hydrostrengthening of a wheel
   Wheels and tires - the general information
   The angles of installation of forward wheels - the general information
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Removal and installation of a steering wheel

All considered models are equipped with a safety cushion. The pillow constantly is in the "alerted" state and can work (to be inflated) at any moment at the connected battery. In order to avoid casual operation of a pillow (and receiving as a result of a trauma) every time when carrying out any works with components of a security system disconnect a negative wire from the battery. After a wire detachment from the battery before getting to work wait at least two more minutes (the system is equipped with the condenser which needs time for a discharge). In more detail about work of a security system see the Head Sistem of onboard electric equipment.


 PERFORMANCE ORDER

  1. Establish the operated car wheels rectilinearly. Disconnect a negative wire from the battery.

If the audio system of your car is equipped with a security code before disconnecting a negative wire from the battery make sure that you have that for input of system in action after completion of works.

  1. Give four fixing nuts and disconnect the safety cushion module from a steering column. Disunite the electric socket of the module. During the work with the module always you hold it the open party from own body. Always put the module on a workbench or other surface the open party up (by no means not down!).
  1. For removal of the module of a safety cushion give the top nuts (right top nuts holds the same position from the opposite side of a steering wheel).

… and the lower nuts (right is located similarly from the opposite side from a steering wheel).

  1. Release lock uvulas and disunite the electric socket of the module of a safety cushion.
  1. Give a nut of fastening of a steering wheel, then mark the provision of a steering shaft on the relation to a nave (if such tags are not put any more or if they are not combined) for the purpose of simplification of the subsequent assembly.

Do not allow a provorachivaniye of a steering shaft after removal of a steering wheel.


  1. Before removal of a steering wheel make sure of combination of adjusting tags on its nave and a pin of a shaft of a column (if those are available); if tags are absent, put them independently by means of a chertilka or white paint.
  1. By means of a stripper remove a steering wheel from a shaft. It is not necessary to force down a wheel from a shaft the hammer at all.
  1. Remove a steering wheel from a shaft only by means of a stripper of NE SBIVYTE ITS HAMMER AT ALL!
  1. If the provision of the operated wheels during the procedure did not change (they remained are directed rectilinearly), now it is possible to establish a steering wheel into place. If wheels turned, it is necessary to make centering of a spiral spring of a safety cushion. For this purpose establish forward wheels strictly rectilinearly and rotate a rotor of an hour spring clockwise against the stop (it is not necessary to make too great efforts). Now turn a rotor on two and a half turns counterclockwise. Pillow module wires - below have to fall into this state of a wire of a horn above, and.

Details of an hour spring of a safety cushion.

  1. For installation of a steering wheel achieve combination of adjusting tags on its nave and a pin of a shaft. Establish a nut and tighten it with the required effort.
  2. Install into place the safety cushion module. Screw four fixing nuts and tighten them with the required effort.
  3. Connect a wire to the negative plug of the battery