Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
- Brake system
   General information
   System of anti-blocking of brakes (ABS) - the general information
   Replacement of blocks of disk brake mechanisms
   Removal, capital repairs and installation of a support of the disk brake mechanism
   Check of a state, removal and installation of a brake disk
   Replacement of boots of drum brake mechanisms
   Removal, capital repairs and installation of wheel cylinders
   Removal and installation of the combined valve (regulator)
   Removal and installation of the main brake cylinder
   Check of a state and replacement of brake hoses and lines
   Pumping of the brake system
   Functioning check, removal and installation of the vacuum amplifier of brakes
   Functioning check, removal, installation and adjustment of the sensor switch of stoplights
   Adjustment of the parking brake
   Replacement of cables of the drive of the parking brake
   Replacement of boots of the parking brake (disk brake mechanisms of back wheels)
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Replacement of cables of the drive of the parking brake

All considered models are equipped with a safety cushion. The pillow constantly is in the "alerted" state and can work (to be inflated) at any moment at the connected battery. In order to avoid casual operation of a pillow (and receiving as a result of a trauma) every time when carrying out any works with components of a security system turn the ignition key in position of LOCK and disconnect a negative wire from the battery. After a wire detachment from the battery before getting to work wait at least two more minutes (the system is equipped with the condenser which needs time for a discharge). In more detail about work of a security system see the Head Sistem of onboard electric equipment.

Forward cable

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.

If the autoradio tape recorder on your car is equipped with a security code before disconnecting a negative wire from the battery make sure available at your disposal a code of connection of the radio tape recorder. Remove the floor console (Head Kuzov).

  1. Release the parking brake. Weaken nuts of fastening of back wheels, a back of the car and establish to a poddomkratta it on props.
  2. Remove an adjusting nut of a forward cable (see an illustration), then disconnect a forward cable from the balance weight.
  3. Release a clamp of a forward cable, then take out an insert from the floor panel.
  1. For a detachment of a forward cable from its arm squeeze a clamp (shooter) by means of a small hose collar of worm type.
  1. For extraction of an insert of a cable from the panel of a floor release lock uvulas (shooters) by means of the screw-driver.
  1. In interior of the car disunite electric sockets of the sensor switch of the parking brake and the module of a safety cushion (in a forward part of the module two electric sockets are located).
  1. For removal of the lever of the parking brake disunite the electric socket of the sensor switch of the parking brake (the central arrow) and give bolts of fastening of the lever (the left and right arrows).
  1. Give fixing bolts and remove the safety cushion module, having shifted it for ensuring access to the lever of the parking brake aside.
  1. For removal of the module of a safety cushion give four fixing bolts (arrow), lift the module up and disunite two of its electric sockets (the second in a picture is not visible).
  1. Give bolts of fastening of the lever of the parking brake, remove assembly of the lever and turn it upside down for ensuring access to a driving cable.
  2. Disconnect a cable of the parking brake from the lever and stretch it through the floor panel.
  3. Remove a floor panel insert from an old cable and put on it new.
  4. You make installation upside-down.
  5. Upon completion of works do not forget to make adjustment of a cable (Section Adjustment of the Parking Brake).

Back cable

 PERFORMANCE ORDER

  1. On models with drum back brake mechanisms remove back wheels. The car also establish to Poddomkratta it on props.
  2. Disconnect a cable from the balance weight and release it from an arm behind the balance weight at once (see an illustration).
  3. Release a cable from clips on elements of a body and the chassis of the car.
  4. On models with drum back brake mechanisms remove brake drums, take off a back boot of the brake mechanism (Section Replacement of Boots of Drum Brake Mechanisms) and disconnect from it a cable. Squeeze a cable clamp a hose collar of worm type and remove it, having passed through a board of the brake mechanism.
  5. On models with disk back brakes disconnect an ear a loop from the executive lever, then squeeze a clamp of fastening of a cable in an arm on a support.
  6. You make installation upside-down.
  7. Upon completion of works do not forget to make adjustment of a cable (Section Adjustment of the Parking Brake).