Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
- Coupling and transmission line
   General information
   Coupling - the general description and check of serviceability of functioning
   Removal and installation of components of hydraulic system of switching off of coupling
   Removal, check of a state and installation of components of coupling
   Removal, check of a state and installation of the release bearing of coupling
   Check of a state and replacement of the directing bearing
   Driveshafts, differentials and bridges - the general information
   Check of a condition of the transmission line
   Removal and installation of driveshafts
   Replacement of cardan hinges
   Replacement of an epiploon of a shaft of the leading gear wheel of differential
   Removal, service and installation of a nave and bearings (forward wheel)
   Removal, capital repairs and installation of a forward power shaft
   Removal and installation of assembly of the forward bridge
   Removal and installation of a back half shaft and assembly of the bearing
   Removal and installation of assembly of the back bridge
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Removal, check of a state and installation of the release bearing of coupling

The dust produced in the course of functioning of coupling and accumulating on a surface of its components may contain noxious to health asbestos. Do not blow off dust compressed air AT ALL and do not inhale it. Do not use for removal of dust solvents on an oil basis or gasoline. For washing off of dust in the pallet it is necessary to use the structures intended for cleaning of brake mechanisms. After completion of cleaning and rubbing of components of coupling merge the used cleaner and put dirty rags in the container marked in a corresponding way.

Removal

Components of assembly of the release bearing


 PERFORMANCE ORDER

  1. Otboltite the executive cylinder from the coupling case (The section Removal and installation of components of hydraulic system of switching off of coupling) also take it from the deepening. Tie up the cylinder aside a wire, trying not to bend and otherwise not to damage the hydraulic line.

Do not disconnect the hydraulic line from the executive cylinder - the system is not subject to pumping in case of hit of air in it!

  1. Remove from the RKPP car (The head the Manual box of gear shifting).
  2. Disconnect the lever of switching off of coupling from a returnable spring and an axial hairpin, take the release bearing from the holder on primary to a shaft and disconnect it from the lever.

Check of a state

 PERFORMANCE ORDER

  1. Holding the central part of the bearing, rotate external, at the same time creating pressing. If the bearing rotates not smoothly and with foreign sounds, replace it. Wipe the bearing with pure rags and check it for existence of signs of wear, cracks and other damages. Do not lower the bearing in solvent - at the same time its factory sealing which is not subject to restoration will be broken. Check the bearing for existence of signs of leaks, in case of identification of those replace assembly.
  2. Check a condition of the lever of switching off and an axial hairpin. The hairpin has to be hardly tightened. Make sure that the lever is not worn-out and is not deformed. Examine a returnable spring of the lever - if it is bent or damaged, make replacement.

Installation

 PERFORMANCE ORDER

  1. Installation in the basic is made as it should be, the return to a removal order. Do not forget to grease slightly directing bearing of a bent shaft, vents of a main shaft of the transmission, the sliding surfaces of the holder of the RKPP bearing, the lever of switching off and its axial hairpin.
  2. Establish to the place of RKPP (The head the Manual box of gear shifting).
  3. Install into place the executive cylinder of coupling (The section Removal and installation of components of hydraulic system of switching off of coupling).