Jeep Grand Cherokee

1993-1999 of release

Repair and operation of the car



Jeep Grand Cherokee
+ Cars of the Jeep Grand Cherokee brand
+ Settings and routine maintenance
+ Line six-cylinder engine
+ V8 engine
+ Procedures of the general and capital repairs of the engine
+ Cooling systems, heating and air conditioning
+ A power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
- Transfer case
   General information
   Adjustment of draft of switching
   Removal and installation of the transfer case
   Capital repairs of the transfer case - the general information
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and methods of operation



Adjustment of draft of switching

NP231

 PERFORMANCE ORDER

  1. On models of 1993 of the issue transfer the transfer case to the mode 4L; on models of 1994 of the issue transfer it to neutral situation. On models of 1995 of the issue transfer the transfer case to situation 4L and enshrine the lever of switching of the modes in this provision, by means of a wire (a coat hanger perfectly will be suitable for clothes).
  2. The car also establish to Poddomkratta it on props.
  3. Weaken a bolt in a choice rod pin.
  1. Weaken a lock bolt in a choice rod pin (NP249 transmission is shown - for NP231 the picture is similar).
  1. Make sure that the lever of switching of the transfer case is in situation 4L (models 1993 and 1994 of of the issue) or in situation "N" (Neutral) (model of 1994 of the issue).
  2. In case of need translate a pin forward or back on a choice rod, then tighten a lock bolt of a pin with the required effort.
  3. Lower the car on the earth and check serviceability of functioning of the device of switching of the transfer case. Carry out trial runs, having made sure of full gearing of the transfer case in provisions 2H, 4H and 4L. If full gearing in all three modes does not happen, make repeated adjustment.

NP242

1993

Components of draft of switching of the NP242 transfer case of models of 1993 of the issue.


 PERFORMANCE ORDER

  1. Remove facing of the lever of switching.
  2. Transfer the lever to situation 4L.
  3. Insert an adjusting pro-rate 3 mm thick (also the drill of the necessary thickness will approach) between the lever of switching and a first line of an aperture under the lever.
  1. For adjustment of draft of switching of the NP242 transfer case of models of 1993 of the issue insert an adjusting pro-rate 3 mm thick (the drill of the required thickness) between the lever of switching and a first line of an aperture under the lever will approach not worse (fix the lever and a pro-rate by means of an insulating tape or a wire).
  1. The car also establish to Poddomkratta it on props.
  2. Under the car weaken a lock bolt of a pin of draft of switching and make sure that the rod of switching is freely established in a pin and the lever.
  3. Make sure that the lever of switching of the modes of the transfer case is in situation 4L.
  4. Freely install a draft rod in the lever of the modes. Strongly tighten a lock bolt of a pin.
  5. Remove jacks and lower the car on the earth.
  6. Remove an adjusting pro-rate (drill) and install into place all earlier removed components.

1994 and 1995

Components of draft of switching of the NP231 transfer case interfaced to RKPP (the same concerns also drafts of switching of NP242 transfer cases of models 1994 and 1995 of of the issue and all boxes of the NP249 type installed complete with RKPP)

Components of draft of switching of the NP231 transfer case interfaced to AT (the same concerns also drafts of switching of NP242 transfer cases of models 1994 and 1995 of of the issue and all boxes of the NP249 type installed complete with AT)

The procedure of adjustment of draft of switching of the NP242 transfer case of models 1994 and 1995 of of the issue is similar that for NP231 1994 (at the switching lever installed in situation "N", but not 4L). See item 1-7.

NP249

The procedure of adjustment of draft of switching of the NP249 transfer case of models 1993 and 1995 of of the issue is similar to NP231 1994, that for a box (at the switching lever installed in situation "N", but not 4L). See item 1-7.